DemarcheISO17025
  • Home
  • PREVIOUS
  • NEXT
Sampling

Sources of Errors During Sampling

Sampling errors inevitably lead to errors in the result, which can have serious consequences for the CAB’s liability. Routine practices and lack of training are the primary sources of errors.

The 5M Method

Sampling and the 5M Method

The use of the 5M method is practically mandatory to include all components that will have a direct or indirect impact on the result.

7.3 - Sampling

7.3.1 The laboratory shall have a sampling plan and sampling method when it carries out sampling of substances, materials, or products for subsequent testing or calibration. The sampling method shall address the factors to be controlled to ensure the validity of subsequent testing or calibration results. The sampling plan and sampling method shall be available at the site where sampling is performed. Sampling plans shall, whenever reasonable, be based on appropriate statistical methods.

7.3.2 Sampling procedures shall describe:

a) the method for selecting samples or sampling locations;
b) the sampling plan;
c) the preparation and treatment of samples from a substance, material, or product in order to provide the information required for subsequent testing or calibration.

7.3.3 The laboratory shall record relevant sampling data as an integral part of the testing or calibration work undertaken. These records shall include, in particular:

a) the reference to the sampling method used;
b) the date and time of sampling;
c) relevant data allowing the sample to be identified and described, such as number, quantity, or name;
d) the identification of the person performing the sampling;
e) the identification of the equipment used;
f) where applicable, the environmental conditions and transport conditions;
g) diagrams or other equivalent means used to identify the sampling location, where applicable;
h) deviations from, additions to, or exclusions from the sampling method and sampling plan.

Methodology

The laboratory must have plans and procedures for carrying out the sampling of substances, materials, and products for future testing, when such sampling falls within the scope of its activities and responsibilities.

The sampling of items to be tested can represent a critical factor in the reliability of test results and in the conformity assessment performed following the tests.

Sampling procedures and sampling plans must be available at the locations where sampling is performed and, if possible, also at the locations where testing and evaluation of test results are carried out.

Sampling procedures and programs must comply with the requirements of existing standards.

In the absence of such requirements, the laboratory must establish and manage its own procedures, taking the following elements into account:

Sampling, transportation, and storage operations must be carried out in such a way as not to alter the original properties of the item being sampled;
All operations must be recorded, including date, time, etc.; the “chain of traceability” must be retrievable and reproducible;
The number, weight, or volume of samples must be established so as to provide statistically significant results in relation to the properties and intended use of the item being sampled.
The sample may be a substance, a matrix, a material, a semi-finished product, part of a product, or an actual product.
The sampling process must take into account all factors that need to be controlled in order to ensure the validity of the sample and of the corresponding results.
Documentation relating to sampling methods must be updated regularly.
Data and operations related to the sampling performed must be recorded.

Any deviations, additions, or exclusions from the documented sampling procedure requested by the customer must be recorded, added to the test documentation, and communicated to the appropriate parties.
Some accreditation bodies accept sampling procedures for accreditation only when they are established by national or international standards or official methods, and only when the laboratory’s scope of accreditation includes tests on samples taken strictly in accordance with those methods.

New technologies, such as tablets and smartphones, allow the sampler to follow the sampling protocol through a dedicated application and to access decision-making support when unforeseen difficulties arise. Virtual reality may one day become part of the sampler’s daily work.

The concept of sample size: samples can have all sizes and shapes, and depending on the context, the definition of a sample by one technician may not be the same as that used by another technician. It can be agreed that a statistical sample consists of a number of units taken from a target population.
However, the sample size may be defined as X samples by personnel concerned with the statistical aspects of a study, but as X individual units by the laboratory analyst.
Because of this difference in terminology, anyone dealing with samples and sampling must be careful when summarizing the sampling process so that there is no misunderstanding.

The concept of a representative sample: a correct sample is defined as “a part of the lot obtained by combining several sublots intended to represent the lot.”
To be acceptable, a sample must be “representative.” There are degrees of representativeness defined by the user, and a representative sample can only be ensured by using proper sampling practices that give each part of the lot an equal and constant probability of being selected as part of the sample.
Any collected material that falls outside the imposed limit for being representative should be classified as non-representative, and vice versa.
Heterogeneity
The reason samples do not exactly reproduce the lot they are intended to represent is due to errors associated with heterogeneity. Heterogeneity is the condition of a population, or a lot, when all individual elements are not identical with respect to the characteristic of interest.

Laboratory subsampling:
There are several reasons for reducing the mass of a laboratory sample. The most common reason is to select the amount of sample required by an analytical protocol, since samples collected in the field are generally much larger than what is needed for laboratory analysis.
The low mass requirements of analytical methods are driven by improved analytical technologies and by cost savings associated with ever smaller quantities of reagents, equipment, and waste per analytical cycle.
It is not obvious how to handle the sample in order to obtain a subsample that is representative of a larger sample.
Another reason for subsampling is that some analyses are repeated using the same method or another analytical method.
Additional analyses may also be performed on the sample, each requiring a separate subsample.

Activities Exemples

Contamination

Dust from other samples Cross-contamination from sampling equipment: equipment not cleaned between two sampling operations. Carryover from the previous sample through contaminated analytical equipment.
Addition of material from abrasion of sampling/preparation equipment: trace analysis of Cr after using stainless-steel sampling equipment;
Corrosion residues from sampling/preparation equipment.
Chemical Modification Reactions causing transformation of the sample: oxidation, hexavalent chromium becoming trivalent chromium.
Loss of chemical constituents: hydrated sample becoming dry upon receipt.
Chemical modification after contact with the sample container or equipment.
Physical alteration Addition of a critical component: water absorption
Loss of a critical component: evaporation of elemental Hg or volatile organic compounds
Loss due to heating or preparation: volatile and semi-volatile compounds evaporated during heating or sample grinding Uneven loss of material due to fractionation
Biological Altération Microbial degradation of an organic compound
Unintentional Errors Dropping the sample
Mixing up labels
Equipment failure
Error in carrying out the method
Transcription error
Intentional Errors Fraud
Sabotage
Copyright © DemarcheISO17025.com